Volkswagen Touran Service Manual: Two-Part Diamond Aluminum Filling Paste

Volkswagen Touran Service Manual / General Paint Information / Original Products / Filling Paste / Two-Part Diamond Aluminum Filling Paste

Definition:

Two-Part Diamond Aluminum Filling Paste, Powder -DA 004 200 A2-

Two-Part Diamond Aluminum Filling Paste, Hardener -DA 004 201 A1-

Two-Part Diamond Aluminum Filling Paste, Hardener -DA 004 211 A1-

Edition 09/2014

Product Description

This filling paste is a polyester filling paste suitable for all types of applications and especially for use in repairing aluminum panels.

It is designed for use in automobile repairs.

This filling paste is pliable and sandable while maintaining a high degree of firmness and temperature stability, which makes it especially suitable to be painted over.

Note

The Hardener -DA 004 211 A1- must be used at temperatures over 30 (86 F) and / or with a relative humidity over 80 %.

Application Instructions

Base Surface

Suitable base surfaces:

Aluminum

Pre-treatment of base surfaces:

Carefully remove any grease and sand the base surface. The base surfaces must be prepared using the → Chapter "Pneumatic Brush Grinder Set -VAS6446-". This means down to the bare metal with P40 grit sandpaper. If necessary, clean the dirty surface once again and then remove any cleaning residue again using the brush grinder.

Processing

Application type:

Apply filling paste.

Mixture ratio:

Both components are mixed in a ratio of 1 part by volume of hardener liquid and 2.5-3 parts by volume of powder or 10 grams of hardener liquid to 25 grams of powder to create a product that can be spread.

Note

Avoid using too much hardener liquid, since this can negatively affect the final strength and adhesion of the filling paste.

Curing Time:

Pot life at +20 (68 F) room temperature for approximately four to six minutes

Reaction Temperature:

Minimum +5 C (41 F)

Drying

Air Drying:

Dry for approximately ten minutes.

Cure using the short-wave IR heater.

Pre-hardening: 10 minutes at 50 C (122 F)

Hardening 1st step: 10 minutes at 75 C (167 F)

Hardening 2nd step: 10 minutes at 85 C (185 F)

Sanding compatibility

Use the body plane to remove any visible excess material before the thermal final curing process. Then use P80 grit dry sandpaper to sand the contours.

Reworking:

No restriction

Note

Use only in well ventilated spaces.

The wearing of protective gloves and dust masks is recommended.

The use of a grinding dust extractor is recommended.

Characteristics

Delivery Viscosity	Powder + Hardener Liquid
Flashpoint:	Hardener 33 C (91.4 F)
Flashpoint:	Powder is not applicable

Storage

The guaranteed shelf life is 12 months from the production date. Use no later than the date indicated on the label and store in original container at +20 C (68 F).

Storage Conditions

Store in a cool and dry place.

Storage temperature +20 C (68 F).

Two-Part IR Premium Filling Paste

Part names: Two-Part IR Premium Filling Paste -LSP 787 220 A1- Two-Part IR Premium Filling Paste -LSP 787 220 A2- ...

Primer Metal

...

Other materials:

Volkswagen Touran Owners Manual. Opening or closing the panoramic sliding roof
Fig. 34 In the roof: turn the switch to open and close Fig. 35 In the roof: push and pull the switch to tilt and close First read and observe the introductory information and safety warnings In order to tilt the panoramic sliding roof, the rotary switch must be in position . ...

Volkswagen Touran Service Manual. Two-Part Epoxy Primer Filler
Definition: Two-Part Epoxy Primer Filler -LLS MAX 220 M1-, beige (250 ml) Two-Part Epoxy Primer Filler -LLS MAX 220 M2-, beige (400 ml) Edition 03/2013 Product De ...