Volkswagen Touran Service Manual: Aquaplus Touch-Up System

Volkswagen Touran Service Manual / General Paint Information / Original Products / Top Coats / Aquaplus Touch-Up System

Definition:

Touch-Up Additive for Aquaplus -LVM 030 000 A2-

Edition 06/2011

Product Description

The touch-up Additive for Aquaplus is especially suited for painting Aquaplus water-based base paint. This serves to simplify the touch-up process.

Application Instructions

Base Surface

Suitable base surfaces:

Primed and filled surfaces (two-part HS filler)

Hardened, solvent-resistant, well-preserved and sanded old paint or factory paints

Suitable pre-treatment materials:

l	Dependent on the object and base surface, according to our structure recommendations.

Pre-treatment of base surfaces:

Clean the factory or old paint or two-part HS filler thoroughly with Silicone Remover -LVM 020 000 A5- or Silicone Remover, Long -LVM 020 100 A5-.

Dry-sand with rotary sander with P400-500 grit and dust extraction or wet-sand with water-resistant P800-1000 grit sandpaper.

Sand the painted area of the undamaged original paint with P1000-1200 grit sandpaper.

Use a suitable cleaning agent before again reworking to ensure a clean and residue-free surface.

Allow wet-sanded surfaces and cleaned surfaces to dry completely.

Processing

Dilution is not required.

Application type "coat"

Processing viscosity 4 mm for +20 C (68 F) , German Industry Standardization 53211

The processing viscosity of the product is ready for immediate application.

Set spray nozzle (see manufacturer's information): "Compliant" 1.2 to 1.3 mm.

Set spray nozzle (see manufacturer's information): "HVLP" WSB/1.3 mm.

Set spray pressure (see manufacturer's information): "Compliant" to 2.0 to 2.5 bar.

Set atomizing pressure (see manufacturer's information): "HVLP" 0.7 bar.

Depending on the color and covering capacity, apply 3 to 5 spray applications of the adjusted Aquaplus water-based base paint using reduced pressure (0.8-1.5 bar) to the damaged areas.

Note

The inlet pressure for this touch-up system should be reduced as described here. Disregard the instructions provided by the manufacturer.

Drying

Evaporating time before clear lacquer application

Let ventilate at +20 C (68 F) room temperature for 15 to 20 minutes.

The following make it possible to reduce the ventilation time:

Applying matt to a painted surface can be accelerated by blowing with a spray gun, forced, IR or oven drying.

Blowing with a spray gun is also possible after waiting at least five minutes.

The drying time is at least 5 minutes.

Reworking

Can be painted over with:

Two-Part HS Clear Coat

Note

The product should not be used "pure".

Personal Protective Equipment:

Note the safety data sheets

Wear the personal protective equipment during application

Characteristics

Flashpoint:

above +23 C (73.4 F)

Storage

The guaranteed shelf life of Touch-Up Additive for Aquaplus -LVM 030 000 A2- is 24 months from date of manufacture. Use no later than the date indicated on the label and store in original container at +20 C (68 F)

Storage Conditions

The optimal storage temperature is between +5 C and +35 C (41 and 95 F).

Note

Temperatures that do not fall within this range can cause damage to the product.

Aquaplus System (Pearl Effect and Heliochrome)

Definition: Water-Based Pearl Effect Base Paint -LPW 040 ...- Water-Based Heliochrome Base Paint -LHW 046 ...- ...

Aqua Premium System

Definition: Water-Based Solid Mixed Paint -LWM 083 ...- Water-Based Metallic/Pearl Effect/Special Effect Mixed Paint ...

Other materials:

Volkswagen Touran Service Manual. Wheel, Balancing with Fine Balancing Machine (Finish Balancer)
Before beginning balancing, the following requirements must be fulfilled. The tire pressure must be OK. The tire profile must not be worn on one side. The tire profile must be at least 4 mm. ...

Volkswagen Touran Service Manual. 6-Pin Universal Oxygen Sensor, Removing and Installing
Note Use the faulty sensor as a guide for installing all of the accompanying attachments, cable ties or marking bands. Do not crimp or cut the wires otherwise the functionality of the heated oxygen sensor (HO2S) will ...