Volkswagen Touran Service Manual: Plastic Primer
Adhesion Promoter (Glazing)
| Adhesion Promoter -ALO 822 000 10- (glazing) |
| The glazing adhesion promoter is a universal
single-component adhesion promoter for all standard exterior
plastic car parts. |
| This adhesion promoter is characterized by its reliable
adhesion, high elasticity and the ease with which it can be
used. |
| All standard plastic parts used on car exteriors. |
| PP, EPDM, ABS, PC, PPO, PA, R-TPU, PBTP, PVC |
|
|
|
| Pre-treatment of base surfaces: |
| The base surface must be free of separating agents. |
| Before cleaning plastic parts, temper them for 60 minutes at
+60 ℃ to "sweat out" the separating agents. |
| |
Clean using Antistatic Plastic Cleaner -LVM 001 001 A2- or a
milder Silicone Remover, Long -LVM 020 100 A5-. |
 Note
| The effort needed for cleaning depends on the type and
quantity of the separating agent used. We recommend using a
sanding pad to help cleaning |
| Let the thinner evaporate (for example, air-drying overnight
at room temperature or 30-40 minutes at +60 ℃). |
|
|
|
| |
Before priming, lightly clean again using Antistatic Plastic
Cleaner -LVM 001 001 A2- or Silicone Remover, Long -LVM 020 100
A5- (antistatic effect). |
|
|
|
| |
Processing viscosity 4 mm for +20 C (68 F), German
Industry Standardization 53211 |
Note
| Do not add any thinner! The delivery viscosity is the same
as the processing viscosity. |
| Processing viscosity 4 mm gravity feed spraygun "Compliant"
and "HVLP": |
|
|
|
| |
Set spray nozzle (see manufacturer's information):
"Compliant" 1.2 to 1.4 mm. |
| |
Set spray nozzle (see manufacturer's information): "HVLP"
1.3 to 1.5 mm. |
| |
Set spray pressure (see manufacturer's information):
"Compliant" to 2.0 to 2.5 bar. |
| |
Set atomizing pressure (see manufacturer's information):
"HVLP" 0.7 bar. |
|
|
|
| |
A preliminary spray application is 1 to 2 mm. |
|
|
|
| Air dry at +20 C (68 F) room temperature, can be sprayed
over after 15 minutes. |
|
|
|
| Can be sprayed over with two-part HS filler elasticized with
Elastic Additive -ALZ 011 001- after drying time at +20 C (68
F). |
| Afterwards, can be painted over with: |
| Water-based base paint and two-part HS clear coat |
|
|
|
| Personal Protective Equipment: |
| Note the safety data sheets |
| Wear the personal protective equipment during application |
|
|
|
| Delivery Viscosity |
11 seconds |
| Flashpoint: |
above +23 C (73.4 F) |
| The guaranteed shelf life is 24 months from production date.
Use no later than the date indicated on the label and store in
original container at +20 C (68 F). |
|
|
|
| The prescribed storage temperature is +20 C (68 F) (not to
fall below +5 C (41 F)). |
|
|
|
Definition:
Two-Part Wash Primer -LHV 043 000 A2-
Edition 10/2010
Product Description
...
Other materials:
Volkswagen Touran Owners Manual. Introduction
This chapter contains information on the following subjects:
→ Warning lamp
→ Checking the electrolyte level of the vehicle battery
→ Charging, replacing, disconnecting and connecting the vehicle battery
The vehicle battery is a component of the electrical s ...
Volkswagen Touran Owners Manual. Using the vehicle in other countries and continents
First read and observe the introductory
information and safety warnings In the factory, the vehicle is produced
specifically for a certain country and complies with this country's registration
regulations valid at the time of vehicle production.
If the vehicle is going to be sold in anothe ...
© 2016-2025 Copyright www.vwtouran.net | 0.0097
Two-Part Wash Primer
Filler