VW Touran manuals

Volkswagen Touran Service Manual: Sprayable Sealant

Definition:
Sprayable Sealant -D 476 KD1 M2-, gray
Sprayable Sealant -D 476 KD2 M2-, black
Edition 08/2012
Product Description
Sprayable Sealant -D 476 KD1 M2-/- D 476 KD2 M2- is a spray-on sealant with a MS polymer base. It hardens into a rubber-elastic material with good abrasion resistance by absorbing atmospheric moisture.
The film formation and hardening time depends on the humidity and temperature. The hardening time is also affected by the layer thickness.
These times can be shortened by raising the temperature and humidity. Lower temperature and humidity levels delay the hardening.
Properties:
Sealant and weld sealant in one product
High stability
Can be sprayed and brushed
Can be painted over with conventional or water-based paints up to three days after applying
Adheres to many materials without glass-/paint primer
High initial strength
Can be spot welded
Silicone-free
No strong odor
Isocyanate-free
Quick drying
UV resistant
High resistance to aging
Sound-dampening properties
Application Instructions
Application
Sprayable Sealant -D 476 KD1 M2-/-D 476 KD2 M2- is used to seal welds in vehicle repair which have been sprayed at the factory, for example in the engine, luggage, and passenger compartment areas. Application tools (telescope spray gun or Pneumatic Cartridge Gun -VAG1761/1-) can be used to reach every desired weld.
The material is used as a surface coating to repair or supplement PVC underbody coating or stone chip protection.
Pretreatment
The adhesion surfaces must be dry, free of oil, dust, grease and any other impurities. Cleaner FL is suitable to clean with.
Adhesion is improved if the contact surfaces are roughened with a sanding pad.
If the material is painted over after completely drying, then the painting preparatory work similar to the plastic preparatory work is to be followed.
  Note
Before starting to apply, it is necessary to read the safety measures and advice in the safety data sheet.
Even for products which are not required to be labeled by law, the usual safety measures must be observed for chemical emissions.
Processing
  Note
Body areas and adhesion surfaces that are to be sealed must be insulated with a Two-Part Filler before applying the material.
Applying Sprayable Sealant -D 476 KD1 M2-/-D 476 KD2 M2- from 310 mL aluminum cartridges can only be performed with the telescope spray gun or Pneumatic Cartridge Gun -VAG1761/1-. These application devices make is possible to apply the material as a strip of material (sealant bead) or to spray it on by using the dual-circuit air system.
The material can be both sprayed and brushed on. This means that it is possible to imitate textured bonds and brushed structures.
The sealed seams can be painted over as early as 15 to 30 minutes.
The corresponding settings on the application devices enable the operator to imitate all textures specified by the manufacturer quickly and conveniently. The spraying distance can be used to vary the width and limit of the bond. Refer to the operating instructions for details on handling and setting the spray gun.
It is recommended to remove any unhardened sealant from the tools using cleaner FL. Hardened material can only be removed mechanically.
Painting procedure
The Sprayable Sealant -D 476 KD1 M2-/-D 476 KD2 M2- can be painted over with one-part and two-part repair paint and even those containing alcohol as a solvent.
Painting over quickly does not prevent complete hardening, it is, however, delayed. Do not wait longer than three days before painting.
Before sealing or coating, phosphate and epoxy resin primers are particularly suitable for corrosion protection. It is imperative that the primers are dry before it is applied.
If the body area to be painted after an accident repair is still to be coated with filler, filler primer or spray-on filler, these materials must be applied before sealing or coating with Sprayable Sealant -D 476 KD1 M2-/-D 476 KD2 M2-.
If a filler still needs to be applied after sealing or coating with Sprayable Sealant -D 476 KD1 M2-/-D 476 KD2 M2-, then the sealant should be at least six hours old and a filler suitable for coating plastic is used.
Incompatibility
The Sprayable Sealant -D 476 KD1 M2-/-D 476 KD2 M2- is not compatible with fresh one-part polyurethane material. Polyurethane products must be solidified before they are sprayed with the sealant.
The material should not be treated with aromatic solvent systems. As a result, it can partially dissolve or swell the sealant.
Technical Data
   
Color Grey, black
Odor Barely perceptible
Consistency pasty
Density approximately 1.6 g/cm³
Stability Excellent
Hardening type Moist hardening
Film formation type (standard climate conditions DIN 50014) 8 to 20 minutes, at +23 C (73.4 F) and a relative humidity of 50 %
Drying (standard climate conditions DIN 50014) Approximately 4 mm/ 24 hours and 6 mm/ 48 hours at +23 C (73.4 F) with a relative humidity of 50 %
Shore A hardness approximately 65
Painting compatibility Can be painted after 20 minutes with one-part and two-part paints
Adhesive properties Bare sheet metal, galvanized metal, EC paint, top coat paint, metallic paint, PVC underbody protective agent, GFK, PP/EPDM (testing recommended)
Chemical resistance Resistant to light and weather, PVC softening agents and fuel (short-term)
Processing temperature +5 C to +35 C (41 to 95 F)
Application temperature -40 C to +90 C (-40 to 194 F) (short-term, up to one hour at +130 C (266 F))
 
     
Storage
The material is not vulnerable to frost.
The guaranteed shelf life is 12 months from the production date. Use no later than the date indicated on the label and store in original container at +10 C to +25 C (50 to 77 F).
  Sprayable Sealant
Polyurethane Adhesive Sealant
Definition: Polyurethane Adhesive Sealant -AKD 476 KD5 05- Edition 04/2009 Product Description ...

Adhesive/Sealant
Definition: Adhesive/Sealant -D 511 500 A2-, gray Adhesive/Sealant -D 511 510 A2-, black Edition ...

Other materials:

Volkswagen Touran Owners Manual. Tyre lettering
Fig. 187 International tyre lettering First read and observe the introductory information and safety warnings  Tyre lettering (example) Meaning Brand name, logo Manufacturer Product name Individual tyre lettering from manufacture ...

Volkswagen Touran Owners Manual. Wheel cover
Fig. 204 Removing the wheel covers First read and observe the introductory information and safety warnings Removing the wheel covers Take the box spanner and wire hook from the tool kit   . Insert the wire hook into one of the holes in the wheel cover. Push the box spanner t ...

© 2016-2024 Copyright www.vwtouran.net | 0.0261