Volkswagen Touran Service Manual: Two-Part Fine Filling Paste, Flexible
Two-Part Fine Filling Paste, Flexible -LSP 787 100 A1- |
The Two-Part Fine Filling Paste, Flexible -LSP 787 100 A1-
is a two component filler paste with high filling
characteristics. |
The product does not collapse and has excellent adhesion on
a multiple base surfaces. |
This filling paste is used especially for plastics: |
For repair of plastic exterior body components where surface
is damaged with material removed (scratches, holes, rips),
without being broken through |
For filling of KU-plastics, that were previously repaired
with the Plastic Repair Set -D 007 700-. |
For filling over a repair area to eliminate a mark |
Constant, fine, creamy consistency |
High filling characteristics - no collapsing |
Good adhesion on metal and plastic |
On all cleaned and sanded plastics in vehicle area |
Fiberglass-reinforced plastics (UP-GF) |
Well-sanded old paint or factory paint |
Hardened two-part filler/two-part primers |
|
|
|
Pre-treatment of base surfaces: |
|
Remove any grease and sand the surface. |
|
Bare metallic base surfaces are to be insulated with
Two-Part Wash Primer -LHV 043 000 A2- and then filled with
Two-Part HS Performance Filler. Sand the filler after drying. |
|
With UP-GF underbodies, clean components of any residual
agents and sand the surface. |
|
|
|
|
Clean once more using the Silicone Remover, Long -LVM 020
100 A5- or Silicone Remover -LVM 020 000 A5- before reworking. |
|
|
|
Fine filling paste by itself. |
Rework fine filling paste with Two-Part Fine Filling Paste -LSP
784 002 A2- or with Two-Part Spray Filling Paste -ALN 788 007-
(except on galvanized steel). |
Prime bare spots and filled areas with Two-Part Wash Primer
-LHV 043 000 A2- and then fill with Two-Part HS Performance
Filler. |
|
Then paint over with the top coat. |
Note
Before filling, dry-sand the entire surface with P280-400
sandpaper. |
|
|
|
Mixing ratio |
2 to 3 % by weight |
Add hardener |
Two-Part Hardener
-LVM 018 00 A1- |
Pot life |
2 to 4 minutes at
+20 C (68 F) |
Drying time
(air drying at +20 C (68 F) room temperature) |
20 to 30 minutes |
Infrared
drying: |
|
|
short-wave |
approximately
three minutes (at 50 % output) |
|
middle-wave |
approximately five
minutes |
Sanding
compatibility |
Preliminary sanding |
Final sanding |
|
Wet |
as fine filling paste
P180 grit |
as fine filling paste
P320-P360 grit |
|
Dry |
as filling paste P80 grit, as
filling paste P120 grit |
as filling paste P120-P240
grit, as fine filling paste P280 grit |
Caution
This filling paste may not be applied to PVB
(acid-hardening) adhesive primers or one-part primers
(for example, synthetic resin). |
Application on thermoplastic or elastic coatings is
also not possible. In these cases, only apply filler
paste to bare steel. |
|
Note
Before filling, dry-sand the entire surface with P280-320
sandpaper. |
Avoid using excessive hardener paste, to prevent it from
bleeding through, especially on daylight colors and light
metallic colors. |
Reaction temperature at least +5 C (41 F). |
|
|
|
Definition:
Two-Part Fine Filling Paste -LSP 784 002 A2-
Edition 06/2011
Product Description
...
Definition:
Two-Part Spray Filling Paste -ALN 788 007-
Edition 06/2011
Product Description
...
© 2016-2024 Copyright www.vwtouran.net | 0.026