Volkswagen Touran Service Manual: Paint System for Plastic Parts

Volkswagen Touran Service Manual / General Paint Information / Original Products / General Application Instructions for Repair and Painting Systems / Paint System for Plastic Parts

This universal painting system enables you to safely and simply paint all plastic parts which can be usually found on the exterior. (Plastic types: PP, EPDM, ABS, PC, PPO, PBTP, UP-GF, PA, PVC, R-TPU, PUR) This technical reference material does not apply to factory primed plastic parts.

Base Surface

Pretreatment of base surfaces:

The base surface must be free of separating agents. Before cleaning the plastic parts, temper them for 60 minutes at +60 ℃ to sweat out the separating agents.

Clean with the Antistatic Plastic Cleaner -LKR 001 001 A3- or a milder Silicone Remover, Long -LSE 20 100 A3-.

The effort needed for cleaning depends on the type and quantity of the separating agent used. It is recommend to use a sanding pad to support the cleaning process. Let the thinner evaporate (for example, air-drying overnight at room temperature or 30-40 minutes at +60 C).

Before priming, lightly clean again using Antistatic Plastic Cleaner -LKR 001 001 A3- or Silicone Remover, Long -LSE 20 100 A3-.

The Paint Structure is not for Primed Plastic Parts.

Primer:

To attain secure adhesion, plastics must be primed after they have been thoroughly cleaned. Here the user has two choices:

1. -

Prime with Two-Part Synthetic Adhesion Filler, White - LKF 696 009- or Two-Part Synthetic Adhesion Filler, Black - LKF 696 040-. The Two-Part Synthetic Adhesion Filler, White -LKF 696 009- and the Two-Part Synthetic Adhesion Filler, Black -LKF 696 040- are primer/fillers which can be directly painted over with top coat.

2. -	Prime with Glazing Adhesion Promoter - ALO 822 000 10- and rework with elastified Two-part HS filler. Further processing with top coat and clear coat.

Notes for Damages:

Small scratches can be filled after priming with Two-Part Fine Filling Paste -LSP 784 002 A2-.

After sanding the filled patches insulate them:

1. -	With Two-Part Synthetic Adhesion Filler, White - LKF 696 009- or Two-Part Synthetic Adhesion Filler, Black - LKF 696 040-.

2. -	Prime with Glazing Adhesion Promoter - ALO 822 000 10- and rework with elastified Two-part HS. Further processing with top coat and clear coat.

For the application instructions, evaporating and drying times refer to the respective technical application information.

→ Chapter "Two-Part Synthetic Adhesion Filler".

→ Chapter "Adhesion Promoter (Glazing)".

→ Chapter "Top Coats".

→ Chapter "Clear Coats".

The Addition of Two-Part Elastic Additive -ALZ 011 001- in Two-part HS Filler.

15 % for rigid and semi-rigid plastics

30 % for highly flexible plastics.

For the application refer to the technical application information of the respective filler. Refer to → Chapter "Filler".

Note

Painted plastic parts may not be cleaned with a high-pressure cleaner before 6 weeks have passed. The minimum distance between the nozzle and the object is 30 cm.

One-Coat Painting

Top Coat:

Mix two-part HS top coat with 15 % Two-Part Elastic Additive -ALZ 011 001- then combine this mixture.

Mixture ratio 3:1 with two-part VHS hardener and 15 % Two-Part Thinner, Special -LVM 009 200 A2-.

Processing:

Apply 1.5 coats.

Let air dry overnight at +20 C (68F)or after 5 to 10 minute final drying time, 30 to 40 minutes at +60 C (140F). When using Two-Part Elastic Additive -ALZ 011 001- use longer drying times.

Two-Coat Painting Solid, Metallic, Pearls

Base Paint:

Water-based base paint with 10 % Purified Water -LVW 010 000 A5-.

Processing:

Apply 1.5 coats.

Clear Coats:

Mix the two-part HS clear coat with Two-Part Elastic Additive -ALZ 011 001-.

Processing:

According to the respective technical application instructions of the clear coat. Refer to → Chapter "Clear Coats".

Drying:

Let air dry overnight at +20 C (68F) or after 10 minute final drying time, 40 to 45 minutes at +60 C (140 F). When using Two-Part Elastic Additive -ALZ 011 001- use longer drying times.

Painting with Satin Finish Paint Shades

One-Coat Painting, Top Coat:

Mix two-part top coat in a 1:1 ratio with Two-Part Matting Component -ALN 775 106- then combine this mixture.

Mixture ratio 4:1 with two-part VHS hardener and 15 % Two-Part Thinner, Special -LVM 009 200 A2-.

Processing:

Apply with two spray applications with 5 to 10 minutes' intermediate drying time for an even paint film surface.

Drying:

Let air dry overnight at +20 C (68F) or after 5 to 10 minutes final drying time 30 to 40 minutes at +60 C (140 F).

Painting in Color Shades with Texture

One-Coat Painting, Top Coat:

Mix two-part HS top coat in a 1:1 ration with Structuring Component, Rough/Fine -ALN 775 107/108- then combine this mixture.

Mixture ratio 4:1 with two-part VHS hardener and 15 % Two-Part Thinner, Special -LVM 009 200 A2-.

Processing:

Two spray applications:

1 Apply normal application, 5 to 10 minutes with intermediate ventilation.

2. Apply the spray coat according to the desired texture.

Let air dry overnight at +20 C (68 F) or after 5 to 10 minutes final drying time 30 to 40 minutes at +60 C (140 F).

Personal Protective Equipment:

Note the safety data sheets

Wear the personal protective equipment during application

Repair Paint System for Matte Painted Vehicles

The following describes the repair paint system for matte painted vehicles. Area of application: large surfaces/complete painting Application ...

Aqua Premium System, Touch-Up System for Two Layer Colors

Product Description/Objective To achieve an optically flawless color shade transition in the blended area or adjacent parts, for example fender/door. ...

Other materials:

Volkswagen Touran Owners Manual. Engine oil consumption
First read and observe the introductory information and safety warnings Engine oil consumption will be different from engine to engine and can change during the working life of an engine. Depending on how you drive and the conditions in which the car is used, oil consumption can be up to 1 ...

Volkswagen Touran Service Manual. Winter tires
M+S-Symbol On "M-and-S-tires", the tread pattern, tread compound or type are designed such that the handling characteristics in snow are improved compared to a normal tire. This is especially true when initiating or maintaining vehicle m ...