VW Touran manuals

Volkswagen Touran Service Manual: Two-Part Fine Filling Paste

Definition:
Two-Part Fine Filling Paste -LSP 784 002 A2-
Edition 06/2011
Product Description
The two-part fine filling paste is a very fine thixotropic polyester filling paste.
This filling paste is suitable for small repairs.
Application Instructions
Properties
Fine and non-porous
Removes easily
Sands easily
High elasticity for touching up synthetic surfaces
Base Surface
Suitable base surfaces:
Steel
Aluminum
Glass fiber reinforced plastics
Old paint and factory paint
Hardened two-part filler/two-part primers
Plastic parts glaze-primed with Two-Part Plastic Adhesive Filler -LKF 696 009 A2-/-LKF 696 040 A2- or Adhesion Promoter -ALO 822 000 10-
Primed surfaces with two-part polyester filling paste.
  Caution
This filling paste may not be applied to PVB (acid-hardening) adhesive primers or one-part primers (for example, synthetic resin).
Application on thermoplastic or elastic coatings is also not possible. In these cases, only apply filler paste to bare steel.
   
Pre-treatment of base surfaces:
  Remove any grease and sand the surface.
  Bare metallic base surfaces are to be insulated with Two-Part Wash Primer -LHV 043 000 A2- and then filled with Two-Part HS Performance Filler. Sand the filler after drying.
  With UP-GF underbodies, clean components of any residual agents and sand the surface.
  Two-Part Fine Filling Paste
  Use a suitable cleaning agent before reworking to ensure a clean and residue-free surface.
  Two-Part Fine Filling Paste
Processing
Application type:
  Apply filling paste.
  Two-Part Fine Filling Paste
Mixture ratio:
  Add 2 to 3 % by weight Two-Part Hardener -LVM 018 000 A1/A2- or, especially when dealing with high temperatures, Two-Part Hardener, Long -LVM 018 100 A2-.
  Note
Avoid using excessive hardener paste, to prevent it from bleeding through, especially on daylight colors and light metallic colors.
Curing Time:
  At +20 C (68 F) room temperature for about three to five minutes.
Reaction Temperature:
  Minimum +5 C (41 F)
  Two-Part Fine Filling Paste
Drying
Air Drying:
  At +20 C (68 F) room temperature for about 20 to 30 minutes.
  Two-Part Fine Filling Paste
Infrared drying:
Short-wave heaters for three minutes (at 50 % power)
Medium-wave heaters for five minutes.
  P00-10028
Sanding compatibility
In connection with the aforementioned drying time:
  Dry-sand the pre-sanding with P180-240 grit sandpaper
  Dry-sand the final sanding with P240-320 grit sandpaper
  Two-Part Fine Filling Paste
  While wet, sand the pre-sanding with P240-320 sandpaper
  While wet, sand the final sanding with P600-800 sandpaper
  Note
When wet-sanding, make sure to wipe and dry off the surface.
Temperature resistance up to +80 C (176 F).
  Two-Part Fine Filling Paste
Reworking
Recommended structure:
One-Part Wash Primer -LVM 044 007 A2-/-LVM 044 171 A2-
Two-Part Wash Primer -LHV 043 000 A2- and Two-Part HS Vario Filler
Two-Part Plastic Adhesive Filler -LKF 696 009 A2-/-LKF 696 040 A2-
Unelasticized Adhesion Promoter -ALO 822 000 10- and Two-Part HS Filler (for plastic parts)
  Then paint over with the top coat.
  Two-Part Fine Filling Paste
Personal Protective Equipment:
Note the safety data sheets
Wear the personal protective equipment during application
Characteristics
  Two-Part Fine Filling Paste
Delivery Viscosity pasty
Flashpoint: Filling paste over 23 C (73.4 F)
VOC value: 2004/42/IIB(b)(250)170 The EU limit for this product (product category IIB.b) in ready-to-use form is a maximum of 250 g/L volatile organic compounds. The VOC-value of this product in ready-to-use form is a maximum of 170 g/L.
 
Storage
The guaranteed shelf life is 12 months from the production date. Use no later than the date indicated on the label and store in original container at +20 C (68 F).
   
Storage Conditions
  Storage Temperature +20 C (68 F) (temperature should not exceed +30 C (86 F)).
  Two-Part Fine Filling Paste
Two-Part Steel Filling Paste Set
Definition: Two-Part Steel Filling Paste Set -DA 787 300 A2- Edition 09/2012 Product Description ...

Two-Part Fine Filling Paste, Flexible
Definition: Two-Part Fine Filling Paste, Flexible -LSP 787 100 A1- Edition 07/2010 Product Description ...

Other materials:

Volkswagen Touran Owners Manual. Tyre pressure
Fig. 184 Location of the tyre pressure plate First read and observe the introductory information and safety warnings The correct tyre pressure for factory-fitted tyres is shown on a sticker - applies to all-season, summer and winter tyres. The sticker   is located on the inside of the ...

Volkswagen Touran Owners Manual. Changing the bulb in the number plate light
Fig. 223 In the tailgate: number plate light Fig. 224 Number plate light: changing the bulb First read and observe the introductory information and safety warnings  The jobs should be carried out in the given order only: 1. Observe a ...

© 2016-2024 Copyright www.vwtouran.net | 0.0076