Volkswagen Touran Service Manual: Two-Part Fine Filling Paste, Flexible

Volkswagen Touran Service Manual / General Paint Information / Original Products / Filling Paste / Two-Part Fine Filling Paste, Flexible

Definition:

Two-Part Fine Filling Paste, Flexible -LSP 787 100 A1-

Edition 07/2010

Product Description

The Two-Part Fine Filling Paste, Flexible -LSP 787 100 A1- is a two component filler paste with high filling characteristics.

The product does not collapse and has excellent adhesion on a multiple base surfaces.

This filling paste is used especially for plastics:

Other Application Areas:

For repair of plastic exterior body components where surface is damaged with material removed (scratches, holes, rips), without being broken through

For filling of KU-plastics, that were previously repaired with the Plastic Repair Set -D 007 700-.

For filling over a repair area to eliminate a mark

Application Instructions

Properties

Constant, fine, creamy consistency

High filling characteristics - no collapsing

Hardens quickly

Sands well

Good adhesion on metal and plastic

Base Surface

Suitable base surfaces:

Steel

Galvanized sheet steel

Aluminum

On all cleaned and sanded plastics in vehicle area

Fiberglass-reinforced plastics (UP-GF)

Well-sanded old paint or factory paint

Hardened two-part filler/two-part primers

Pre-treatment of base surfaces:

Remove any grease and sand the surface.

Bare metallic base surfaces are to be insulated with Two-Part Wash Primer -LHV 043 000 A2- and then filled with Two-Part HS Performance Filler. Sand the filler after drying.

With UP-GF underbodies, clean components of any residual agents and sand the surface.

Clean once more using the Silicone Remover, Long -LVM 020 100 A5- or Silicone Remover -LVM 020 000 A5- before reworking.

Reworking

Recommended structure:

Fine filling paste by itself.

Rework fine filling paste with Two-Part Fine Filling Paste -LSP 784 002 A2- or with Two-Part Spray Filling Paste -ALN 788 007- (except on galvanized steel).

Prime bare spots and filled areas with Two-Part Wash Primer -LHV 043 000 A2- and then fill with Two-Part HS Performance Filler.

Then paint over with the top coat.

Note

Before filling, dry-sand the entire surface with P280-400 sandpaper.

Application Table

Mixing ratio		2 to 3 % by weight
Add hardener		Two-Part Hardener -LVM 018 00 A1-
Pot life		2 to 4 minutes at +20 C (68 F)
Drying time (air drying at +20 C (68 F) room temperature)		20 to 30 minutes
Infrared drying:
	short-wave	approximately three minutes (at 50 % output)
	middle-wave	approximately five minutes
Sanding compatibility		Preliminary sanding	Final sanding
	Wet	as fine filling paste P180 grit	as fine filling paste P320-P360 grit
	Dry	as filling paste P80 grit, as filling paste P120 grit	as filling paste P120-P240 grit, as fine filling paste P280 grit

Caution

This filling paste may not be applied to PVB (acid-hardening) adhesive primers or one-part primers (for example, synthetic resin).

Application on thermoplastic or elastic coatings is also not possible. In these cases, only apply filler paste to bare steel.

Note

Before filling, dry-sand the entire surface with P280-320 sandpaper.

Avoid using excessive hardener paste, to prevent it from bleeding through, especially on daylight colors and light metallic colors.

Reaction temperature at least +5 C (41 F).

Two-Part Fine Filling Paste

Definition: Two-Part Fine Filling Paste -LSP 784 002 A2- Edition 06/2011 Product Description ...

Two-Part Spray Filling Paste

Definition: Two-Part Spray Filling Paste -ALN 788 007- Edition 06/2011 Product Description ...

Other materials:

Volkswagen Touran Service Manual. Inspecting Tires
Because tire damage can have serious consequences, the technician and the driver should regularly check the tires, as it is the best form of early problem recognition. Pre-damaged tires cannot withstand driving situations like high vehic ...

Volkswagen Touran Service Manual. Hoses, Repairing
General Information A new repair concept has been developed for repairing washer system hoses. Various individual hose connectors, adapters, Ethylene Propylene Diene Methylene (EPDM) rubber hoses and shrink tubing will be offered as replacement parts. ...