VW Touran manuals

Volkswagen Touran Service Manual: Blender

Volkswagen Touran Service Manual / General Paint Information / Original Products / Clear Coats / Blender

Definition:
Blender -LVE 013 100 A2-
Edition 10/2012
Product Description
Blender was developed for hassle-free two-part clear coat and top coat touch-up.
Properties:
Easy to use (pure)
Applies well to all base surfaces
Blends well with the old paint
Application Instructions
Preparation
Applying base paint:
Keep the filler surface as small as possible.
Paint filler spot thoroughly with water-based base paint (overlapping spray applications)
   
Touch-Up System for Two-Part Clear Lacquers
Mixing ratio for two-part clear coat:
l  Adjust the two-part clear coat according to technical application information. Refer to → Chapter "Clear Coats".
  Blender
Painting:
  Paint over the water-based base paint with adjusted clear coat (overlapping spray applications).
  Blender
Touch-up process:
  Apply pure Blender -LVE 013 100 A2- onto the touch-up area inside the sanded surface.
  Blender
Touch-Up System for Two-Part Top Coats
Mixing ratio for two-part top coat:
l  Adjust the two-part top coat according to technical application information. Refer to → Chapter "Top Coats".
  Blender
Painting:
  Paint over filler area thoroughly (overlapping spray applications).
  Blender
Touch-up process:
  Apply pure Blender -LVE 013 100 A2- onto the touch-up area inside the sanded surface.
  Blender
Polishing the Touch-Up Zones
Air dry at +20 C (68 F) room temperature:
Polish the touch-up areas after they have dried overnight
  Blender
Final drying time with forced drying is a minimum of 5 to 10 minutes.
  Blender
Forced drying is at +60 C (140 F) object temperature for 30 minutes.
  After that, allow the touch-up areas to cool off for an hour and polish at +20 C (68 F) room temperature.
  Blender
Final drying time for IR drying is a minimum of 5 to 10 minutes.
  Blender
IR dry with a short-wave radiator for 10 minutes
  After that, allow the touch-up areas to cool off for an hour and polish at +20 C (68 F) room temperature.
  Note
Polish the touch-up area with fine polishing paste by hand or with a polishing machine.
To finish, treat the surface with high-gloss sealant.
  Blender
Personal Protective Equipment:
Note the safety data sheets
Wear the personal protective equipment during application
Characteristics
  Blender
Flashpoint: +20 C (68 F)
 
     
Storage
The guaranteed shelf life of 60 months from date of manufacture. Use no later than the date indicated on the label and store in original container at +20 C (68 F).
  Blender
    Two-Part HS Performance Clear Coat
    Definition: Two-Part HS Performance Clear Coat -LZK 769 K06 A5- Edition 08/2012 Product Description ...

    Hardener
    ...

    Other materials:

    Volkswagen Touran Owners Manual. New wheels and tyres
    First read and observe the introductory information and safety warnings New tyres Drive particularly carefully for the first 600 km with new tyres as the tyres have to be run in. Tyres that have not been run in have reduced grip   and braking effect  . All four wheels must ...

    Volkswagen Touran Service Manual. Tire Pressure Monitoring Sensor without Valve, Removing and Installing, Vehicle Before Customer Delivery
    Special tools and workshop equipment required Torque Wrench -VAG1410- Perform the Following: Removing   Remove the tire from the disc wheel.   ...

    © 2016-2019 Copyright www.vwtouran.net | 0.0034