VW Touran manuals

Volkswagen Touran Service Manual: One-Part Clear Coat

Definition:
One-Part Clear Coat -LLS MAX 010-
Edition 10/2008
Product Description
The One-Part Clear Coat -LLS MAX 010- is a single-compound product. The raw material base is acrylic resin.
Properties:
Easy application (one-part material)
Dries quickly
High gloss
Universal usage
Easy polishing
Application Instructions
Application
Repair work and partial painting
Base Surface
Suitable base surfaces:
Solvent or water-based base paints
The base paint can be painted over with One-Part Clear Coat -LLS MAX 010- after 30 minutes.
   
Pre-treatment of base surfaces:
  The base surface must be free of dust and grease.
  One-Part Clear Coat
Processing
For work safety, wear appropriate, personal protective equipment.
Latex or nitrile protective gloves, for example
Breathing mask, for example type A2/P2
Application:
  Thoroughly shake the can for at least two minutes and perform a short "spray test".
  One-Part Clear Coat
Application type "coat"
  Apply two to three spray applications with a 5 to 10 minute intermediate ventilation time.
  The recommended dry layer thickness is between 30 and 40 mm.
Spraying distance:
  Maintain a distance of 20 to 25 cm.
  Note
If the spraying procedure is interrupted, make sure that the valve above the spray head is empty to prevent any nozzle blockage.
  One-Part Clear Coat
Drying
Air drying at +20 C (68 F) room temperature is:
Dust dry after 10 minutes
Firm coating after 20 minutes
Polishable after 12 hours
  One-Part Clear Coat
IR drying is possible with this product. With short-wave heater, the IR drying is seven minutes.
Further Processing
  The One-Part Clear Coat -LLS MAX 010- can be polished after 12 hours of air drying at +20 C (68 F) room temperature using a commercially available polish.
  Caution
For work safety, wear appropriate, personal protective equipment.
Note the safety data sheets as well as the warnings on the label of the spray nozzle.
Shake briefly again before every subsequent spray application.
Dispose of the empty spray cans as recyclable material.
Characteristics
  One-Part Clear Coat
Solid matter content 20% by weight
Yield Approximately 0.5 m² to 075 m²/spray can with 30 - 40 μm dry layer thickness
Gloss level 90 units (60 measurement geometry)
Note Used only by a professional
VOC value: The EU limit for this product (product category IIB.b) in ready-to-use form is a maximum of 629 g/L volatile organic compounds. The VOC value of this product in ready-to-use form is a maximum of 252 g/can.
 
     
Storage
The guaranteed shelf life of 60 months from date of manufacture. Use no later than the date indicated on the label and store in original container at +20 C (68 F).
  One-Part Clear Coat
One-Part Test Paint
Definition: One-Part Test Paint -LLS MAX 005-, black Edition 10/2008 Product Description ...

One-Part Wash Primer
Definition: One-Part Wash Primer -LLS MAX 106 M2-, light gray One-Part Wash Primer -LLS MAX 107 M2-, dark gray ...

Other materials:

Volkswagen Touran Owners Manual. Seat heating
Fig. 48 In the centre console: controls for the front seat heating, set here to the second heating level First read and observe the introductory information and safety warnings The seat cushions can be heated electrically when the ignition is switched on. In some versions, the backrest ...

Volkswagen Touran Service Manual. Run-Flat Tire, Seal Inside-Technology
The vehicle can be equipped with run-flat tires as an option. The Seal Inside technology is a system that allows the vehicle to continue driving even if the tire has been punctured by a nail or screw: a protective coating on the in ...

© 2016-2024 Copyright www.vwtouran.net | 0.0252