Volkswagen Touran Service Manual: Two-Part HS Vario Clear Coat
Two-Part HS Vario Clear Coat -L2K 769 K01 A5- |
Two-part HS vario clear coat is a VOC compliant (VOC value
less than 420 g/L), high-quality and productive high solid clear
coat. |
Easy and quick to process |
Variable uses for two-part HS and two-part VHS hardeners |
Good spreading properties |
Suitable preliminary coatings: |
|
|
|
Processing with Two-Part HS Hardeners |
Two-Part HS Hardener -LHA 009 041 A3- |
Two-Part HS Hardener, Short -LHA 021 004 A3- |
Two-Part HS Hardener, Long -LHA 009 047 A3- |
Two-Part HS Hardener, Extra Long -LHA 009 048 A3- |
For Elastification. Refer to
→ Anchor. |
|
|
|
Processing time/pot life: |
|
Ready to spray in 60 to 90 minutes at +20 C (68 F)
(depending on the hardener used) |
|
|
|
|
Processing viscosity at +20 C (68 F) material temperature
is the mixing viscosity for "Compliant" and "HVLP". |
|
|
|
|
Set spray nozzle (see manufacturer's information):
"Compliant" 1.2 to 1.3 mm. |
|
Set spray nozzle (see manufacturer's information): "HVLP"
1.3 to 1.4 mm. |
|
Set spray pressure (see manufacturer's information):
"Compliant" to 2.0 to 2.5 bar. |
|
Set atomizing pressure (see manufacturer's information):
"HVLP" 0.7 bar. |
|
|
|
Note
During the spray application process, the first half spray
application should form a thin, nearly complete film upon which
a fully-completed spray application can be applied. |
|
The recommended dry layer thickness is between 50 and 60 mm. |
|
|
|
Processing with two-part VHS hardeners |
Two-Part VHS Hardener -LHA 009 051 A2-/-LVM 009 051 A5- |
Two-Part VHS Hardener, Short -LHA 009 050 A2- |
Two-Part VHS Hardener, Long -LHA 009 052 A2-/-LHA 009 052
A3- |
Two-Part VHS Hardener, Extra Long -LHA 009 053 A2- |
See technical application information for the two-part VHS
hardener. Refer to
→ Chapter "Two-Part VHS Hardener and Two-Part VHS Performance
Hardener". |
Two-Part Thinner, Special -LVM 009 200 A2-/-LVM 009 200 A5- |
Two-Part Thinner, Long -LVM 009 300 A2- |
HS Spot Thinner -LVM 006 000 A2-. Observe the technical
application information. Refer to
→ Chapter "HS Spot Thinner". |
For Elastification. Refer to
→ Anchor. |
|
|
|
Processing time/pot life: |
|
Ready to spray in 60 to 90 minutes at +20 C (68 F)
(depending on the hardener used) |
|
|
|
|
Processing viscosity at +20 C (68 F) material temperature
is the mixing viscosity for "Compliant" and "HVLP". |
|
|
|
|
Add 12.5 % Two-Part Thinner, Special -LVM 009 200 A2-/-LVM
009 200 A5- /Two-Part Thinner, Long -LVM 009 300 A2- at + 20 C
(68 F) material temperature. |
|
|
|
|
Set spray nozzle (see manufacturer's information):
"Compliant" 1.2 to 1.3 mm. |
|
Set spray nozzle (see manufacturer's information): "HVLP"
1.3 to 1.4 mm. |
|
Set spray pressure (see manufacturer's information):
"Compliant" to 2.0 to 2.5 bar. |
|
Set atomizing pressure (see manufacturer's information):
"HVLP" 0.7 bar. |
|
|
|
Note
During the spray application process, the first half spray
application should form a thin, nearly complete film upon which
a fully-completed spray application can be applied. |
When using as a clear coat for minimal damage repairs
(clever repair procedure), 12.4 % Two-Part Thinner, Special -LVM
009 200 A2- can be replaced with 12.5 % HS Spot Thinner -LVM 006
000 A2-. Do not apply on slanted surfaces. |
|
The recommended dry layer thickness is between 50 and 60 mm. |
|
|
|
Air dry at +20 C (68 F) room temperature: |
Dust dry after 20 to 30 minutes |
Ready for assembly after 4 to 5 hours |
|
|
|
Final drying time with forced drying is a minimum of 5 to 10
minutes. |
|
|
|
Forced dry at +60 C (140 F) object temperature for 20 to
30 minutes |
|
|
|
Final drying time for IR drying is at least 5 minutes. |
|
|
|
IR dry with a short-wave heater for 10 to 15 minutes and
with a medium-wave heater for 15 to 20 minutes |
|
|
|
Elastification for rigid and semi-rigid plastics: |
The base material must first be mixed with 15 % Elastic
Additive -ALZ 011 001-. |
Mixture with two-part HS hardeners, 2:1 |
Mixing two-part VHS hardeners, 3:1 with 20 % thinner (drying
extends this). |
When using as a clear coat for minimal damage repairs
(clever repair procedure), 12.5 % Two-Part Thinner, Special -LVM
009 200 A2-/-LVM 009 200 A5- can be replaced with 12.5 % HS Spot
Thinner -LVM 006 000 A2-. Do not apply on slanted surfaces. |
|
|
|
Personal Protective Equipment: |
Note the safety data sheets |
Wear the personal protective equipment during application |
|
|
|
Flashpoint: |
above +23 C (73.4 F) |
VOC value: 2004/42/IIB(d)(420)420 |
The EU limit for this product
(product category IIB.b) in ready-to-use form is a maximum of 420 g/L
volatile organic compounds. The VOC-value of this product in
ready-to-use form is a maximum of 420 g/L. |
The guaranteed shelf life of Two-Part HS Vario Clear Coat
-L2K 769 K01 A5- is 48 months from date of manufacture. Use no
later than the date indicated on the label and store in original
container at +20 C (68 F). |
|
|
|
Definition:
Two-Part MS Matt Clear Coat -L2K 769 020 A2-
Edition 08/2013
Product Description
...
Definition:
Two-Part HS Optimum Clear Coat -LZK 769 K02 A5-
Edition 10/2012
Product Description
...
Other materials:
Volkswagen Touran Owners Manual. Introduction
This chapter contains information on the following subjects:
→ Display
→ Function
The road sign recognition system can help the driver check the speed limits or
overtaking restrictions that currently apply for him. The road signs and additional
information recognised ...
Volkswagen Touran Owners Manual. Waxing and polishing the vehicle
First read and observe the introductory
information and safety warnings Waxing
Waxing protects the paintwork. You will need to wax the vehicle with a good
hard wax at the latest when the water does not clearly form
small drops and run off the paintwork when it is clean.
Even if a wax solut ...
© 2016-2024 Copyright www.vwtouran.net | 0.0251