VW Touran manuals

Volkswagen Touran Service Manual: Two-Part HS Optimum Clear Coat

Definition:
Two-Part HS Optimum Clear Coat -LZK 769 K02 A5-
Edition 10/2012
Product Description
Two-part HS optimum clear coat is a VOC compliant (VOC value less than 420 g/L), high-quality and productive high solid clear coat.
Properties:
Easy and economical processing
Very good spreading properties
Dries very quickly
Very good IR drying
Quick and easy to polish
High-gloss result
Application Instructions
Base Surface
Suitable preliminary coatings:
Water-based base paints
   
Processing
Mixture ratio:
  3:1 by volume with:
Two-Part VHS Hardener -LHA 009 051 A2-/-LVM 009 051 A5-
Two-Part VHS Hardener, Short -LHA 009 050 A2-
Two-Part VHS Hardener, Long -LHA 009 052 A2-/-LHA 009 052 A3-
Two-Part VHS Hardener, Extra Long -LHA 009 053 A2-
See technical application information for the two-part VHS hardener. Refer to → Chapter "Two-Part VHS Hardener and Two-Part VHS Performance Hardener".
For elastification → Anchor.
  Two-Part HS Optimum Clear Coat
Processing time/pot life:
  Ready to spray in 80-100 minutes at +20 C (68 F)
  Two-Part HS Optimum Clear Coat
Application type "coat"
  Two-Part HS Optimum Clear Coat
  Processing viscosity at +20 C (68 F) material temperature is the mixing viscosity for "Compliant" and "HVLP".
  Two-Part HS Optimum Clear Coat
  Set spray nozzle (see manufacturer's information): "Compliant" 1.2 to 1.3 mm.
  Set spray nozzle (see manufacturer's information): "HVLP" 1.3 to 1.4 mm.
  Set spray pressure (see manufacturer's information): "Compliant" to 2.0 to 2.5 bar.
  Set atomizing pressure (see manufacturer's information): "HVLP" 0.7 bar.
  Two-Part HS Optimum Clear Coat
  Apply 1.5 coats.
  Note
During the spray application process, the first half spray application should form a thin, nearly complete film upon which a fully-completed spray application can be applied.
  The recommended dry layer thickness is between 45 and 55 mm.
  Two-Part HS Optimum Clear Coat
Drying
Air dry at +20 C (68 F) room temperature:
Dust dry after 40 to 50 minutes
Ready for assembly after 4 to 6 hours
Dry overnight
  Two-Part HS Optimum Clear Coat
Final drying time with forced drying is a minimum of 5 to 10 minutes.
  Two-Part HS Optimum Clear Coat
Forced drying at +60 C (140 F) object temperature with:
Two-Part VHS Hardener -LHA 009 051 A2-/-LVM 009 051 A5- for 20 to 25 minutes.
Two-Part VHS Hardener, Short -LHA 009 050 A2- for 15 to 20 minutes.
Two-Part VHS Hardener, Long -LHA 009 052 A2-/-LHA 009 052 A3- for 20 to 30 minutes.
Two-Part VHS Hardener, Extra Long -LHA 009 053 A2- for 25 to 35 minutes.
  Two-Part HS Optimum Clear Coat
Final drying time for IR drying is a minimum of 5 to 10 minutes.
  Two-Part HS Optimum Clear Coat
IR dry with short-wave heater for 8 to 12 minutes
  Two-Part HS Optimum Clear Coat
Special Instructions
Elastification for rigid and semi-rigid plastics:
The base material must first be mixed with 15 % Elastic Additive -ALZ 011 001-.
Mixing two-part VHS hardeners, 3:1 with 5 % thinner (drying extends this).
  Two-Part HS Optimum Clear Coat
Personal Protective Equipment:
Note the safety data sheets
Wear the personal protective equipment during application
Characteristics
  Two-Part HS Optimum Clear Coat
Flashpoint: above +23 C (73.4 F)
VOC value: 2004/42/IIB(d)(420)420 The EU limit for this product (product category IIB.b) in ready-to-use form is a maximum of 420 g/L volatile organic compounds. The VOC-value of this product in ready-to-use form is a maximum of 420 g/L.
 
     
Storage
The guaranteed shelf life of Two-Part HS Optimum Clear Coat -LZK 769 K02 A5- is 48 months from date of manufacture. Use no later than the date indicated on the label and store in original container at +20 C (68 F).
  Two-Part HS Optimum Clear Coat
Two-Part HS Vario Clear Coat
Definition: Two-Part HS Vario Clear Coat -L2K 769 K01 A5- Edition 06/2013 Product Description ...

Two-Part HS Optimum Plus Clear Coat
Definition: Two-Part HS Optimum Plus Clear Coat -LZK 769 K07 A5- Edition 04/2013 Product Description ...

Other materials:

Charging Systems not Requiring a Permit
At this time, A/C service units for extracting, cleaning and filling refrigerant for motor vehicle A/C systems are available from various manufacturers. Charging systems not requiring a permit are ones used for transferring compressed ga ...

Aqua Premium System, Touch-Up System for Three Layer Colors
Product Description/Objective To achieve an optically flawless color shade transition in the blended area or adjacent parts, for example fender/door. Application Instructions Base Surface ...

Condenser
  Caution Non-approved tools or materials such as leak sealing additives can cause damage or malfunctions in the system. Only use tools and materials approved by the manufactu ...

© 2016-2019 Copyright www.vwtouran.net